Previous Topic: Detectors: Conduction in a Solid Lecture Index Next Topic: Detectors: CCDs

ASTR 5110, Majewski [FALL 2011]. Lecture Notes

ASTR 5110 (Majewski) Lecture Notes



  • One can dramatically alter the conductivity of a semiconductor by "preloading" it with an excess of conduction electrons or holes.
    • Add to molten valence 4 elements impurities of valence 3 or valence 5 elements. When crystallizes, the impurities are incorporated into the crystal lattice.
    • Can also add valence 3 or 5 impurities by high speed injection.

    • The net effect is to generate some allowed energy levels in the normal forbidden bandgap zone into which electrons can jump from the valence band (P-type doping) or in which electrons already exist to jump into the conduction band (N-type doping). In either case, the normal bandgap energy is "short circuited".

  • N-Type Doping: Column Va element has 5 valence electrons --> surplus 1 electron in the lattice that is relatively easily detached to conduction band. Can tune lattice with a density of impurity that exceeds the number of thermal and photo-excited (Egap=hf) electrons if desired.
  • .

    "Donor", or N-type impurity added

    • From an energy level standpoint, the effect of N-type doping is to greatly decrease the effective energy bandgap to Ei. At normal temperatures, this allows there to be an excess of electrons available for electrical conduction.

  • P-Type Doping: Column IIIa element has 3 valence electrons --> shortage of electrons, surplus of holes. Atoms want to capture electrons from valence 4 atoms - holes migrate and conductivity again increases.

  • "Acceptor", or P-type impurity added

    • From an energy level standpoint, the effect of P-type doping is to create an energy level close to the valence band into which it is easy for an electron to jump from the valence band.

    • Ei is the (small) energy needed to excite an electron from top of valence band into acceptor level and thereby "bind the hole" into the valence band. At normal temperatures, the existence of extra holes in the valence band allows electrical conduction of holes.

  • In summary:

    The point of doping is:

    • For photon sensitivity: Change the wavelength sensitivity of a semiconductor by effectively changing the energies that can be absorbed with the newly created bandgap energy levels.

      • Thus, we can dope standard semiconductors to increase their sensitivity to longer (redder) wavelengths.

    • For electrical conductivity: "Pre-load" a material with an excess of electrons or holes.

      • Much work with semiconductors in circuitry involves cleverly combining insulators and p-doped and n-doped substances to make a variety of junctions.

(Operation of a single pixel)

We now turn to an important kind of a semiconductor junction -- the metal oxide semiconductor (MOS) capacitor -- that is the foundation of the pixel in the CCD and other instruments.

  • Made by covering a semiconductor with a thin layer of insulating material like SiO2.
  • Add a small electrode (gate) on top
  • If add positive charge to gate, free electrons in semiconductor move towards gate (and holes away) but they can't cross the insulator. This is a capacitor.
  • P-Type Substrate: Now if we make the substrate out of a p-doped semiconductor and put the gate at +10 V:

    • The holes move away from the gate as before, but there are virtually no free electrons to move closer to SiO2.

    • The region near the SiO2 layer is called a depletion region or depletion zone.
    • Thus, if there are no thermally created electron-hole pairs, i.e. the device is cold, only photoelectrons will collect near the Si-SiO2 interface (represented by the one, circled "-" shown below).
    • The depletion region can be thought of as a well, where photoelectrons are stored. The size of the well is proportional to the gate voltage.
    • The voltage applied to a gate is called the bias voltage (note connection to "bias frame" discussed later).
    • The maximum charge (number of electrons) a pixel can hold is called the well capacity.
      • Well capacity generally given in units of e-.
        E.g. CCDs typically can hold > 150,000 e-/pixel.
      • The well depth (and the system electronics) affect the possible dynamic range of the device.
        E.g. with the CCD pixel above, only about 150,000 different levels recordable.
    • Obviously, the key to integration is being able to create and store photoelectrons in the pixel wells.

    • How do we monitor the total charge collected in the pixels?
      • One way is to switch the gate voltage and drive the electrons into the substrate where it can be collected and read as a current:

        This readout method is called a Charge Injection Device.


  • An alternative readout method is the heart of a Charge-Coupled Device (CCD).
  • Imagine two gates on same substrate --> two depletion zones.
  • If the gates are far enough, the wells are independent.
  • But, if gates are placed only about 1 micron apart, the depletion zones can "communicate".
  • By fiddling with voltages, can transfer charge packets from one to the other; electrons seek deeper well (i.e. they are attracted to the larger gate voltage).
  • The gates in this configuration for the basis of the Charge Transfer Mechanism.
  • Now imagine rows of gates along a substrate and the ability to move charge along the substrate from gate to gate like a bucket brigade --> this is the essence of the Charge-Coupled Device (CCD).

Previous Topic: Detectors: Conduction in a Solid Lecture Index Next Topic: Detectors: CCDs

P-type and N-type images from All material copyright © 2002,2009,2011 Steven R. Majewski. All rights reserved. These notes are intended for the private, noncommercial use of students enrolled in Astronomy 5110 at the University of Virginia.